NETXPERT 1400

The NetXpert 1400 provides a complete solution for cable qualification and troubleshooting of active networks, enabling rapid, simple verification and documentation of the capability of cabling links to support Gigabit Ethernet operation compliant with the IEEE 802.3ab standard. A “Pass/Fail” result indicates whether the existing cabling can support data rates up to 1Gbit/s.

  • Gigabit LAN Qualifier with Network Diagnostic Tool
  • Easy Cable Testing and Ethernet Speed Certification

The NetXpert 1400 is a cost-effective alternative for installers and operators of network cabling systems where qualifying cabling bandwidth up to Gigabit Ethernet is sufficient. The NetXpert 1400 allows users to verify whether cabling links will support a maximum data rate of up to 1Gbit/s irrespective of the category of the cables, patch panels, or outlets installed. Performing standards-based tests with real data as per IEEE 802.3ab and bit error rate tests (BERT) the NetXpert 1400 tests the error free data transmission at 100 MBit/s or 1Gbit/s. In addition, parameters affecting signal quality can be displayed including signal-to-noise ratio (SNR) and dely skew. Delay skew in a 4-pair cable indicates the signal time delay between pairs and can impact Gigabit Ethernet performance.

  • Tests network and coaxial cabling
  • Qualifies data cabling for IEEE 802.3 compliance at transmission rates of up to 1Gbit/s (BERT)
  • Determines signal-to-noise ratio (SNR)
  • Measures delay skew
  • Performs full TDR for pair length and distance to fault measurements
  • Full- colour wire map shows opens, shorts, miswires, and split pairs
  • Results can be saved in the tester, and standards-based measurement
  • Reports showing ”Pass/Fail“ results can be generated
Item Specification
 Measurement Technology Time Domain Reflecometry (TDR) and Capacitance
 Cable Measurements Cable Testing and ID: up o 1,000 ft (305 m)
Split Pair Detection: 3 ft (1 m to 1,000 ft (305 m)
Length Measurement: 0 to 1,500 ft (457 m), ± (5%+1ft
Distance to fault: 0 to 200 m ± (5% + 1m)
Supports 8 continuity and ID numbes remotes (RJ 45)
Supports 20 RJ 45 and 20 F connector ID only remotes
 Power over Ethernet Tests for IEEE 802.3af and IEEE 802.3at (PoE +) compliant PoE
Tests for classes and loads cable up to 25.5 watts (t class 4 Identifies Mode A or B (pas with PoE))
 Active Ethernet Indicates advertised speeds of 10/100/1000 base-T half or full duplex
Can Link to network at 10/100 base-T
 Maximum Voltage Parameters refer to the maximum voltage that can be applied to any 2 connector pins
without causing damage to the tester.
– RJ Jack: 66 Vdc or 55 Vac
– F-connector: 50 Vdc or Vac
 Save Test Result Stores up to 250 Cable or network tests with user defined names per project
 Tone Generation Tone Generation
 Languages English, French, German
 Battery Li-Ion Akku, 7,2 VDC, 5,500 mA-hr (typical) Battery Life – Linked @ 1Gb – 1 hrs min., 20 hrs stand-by
 Temperature Operating: 14 to 140° F (-10 to 60°C) Storage: -22 to 158°F (-30 to 70°)
 Humidity 10 to 90% non-condensing
 Enclosure High-strength PC/ABS plastic with VO rating with boot Withstands 4 foot (1,20m) drop on to concrete
 Display 3,5“ Color Touch Screen Display
 Size 6 x 10 x 23 cm
 Weight With batteries: 1 lb 12 oz 508 g)

Featuring a bundle of network testing capabilities, the NetXpert 1400 assists you with verifying network configuration and troubleshooting as ay moves, adds & changes (MACs) performed will require a renewed verification. The NetXpert 1400 verifies, when connected to a communications outlet, if a link can be established to the switch and which connection speeds are supported (up to 1Gbit/s). The Ping test detects the availability of individual and lists of IPv4 and IPv6 addresses and any user-selectable URLs. On top of this, the user can choose from a range of other network tests, such as LLDP/CDP/NDP and VLAN discovery and comprehensive PoE (Power over Ethernet) tests, including a load test.

The full-colour touch screen and another 4 buttons make the NetXpert 1400 easy to use while the high resolution colour screen guarantees excellent readability in any environment. Its ruggedised design is ideally suited for rough handling environments. Test reports and documentation and be generated directly on the device.

  • Link test up to 1 Gbit/s to identify link capability and link status
  • Ping to a single or lists of IPv4 and IPv6 addresses (Ipv6 planned) as well as any URL on the internet
  • CDP/LLDP/NDP and VLAN discovery
  • PoE / PoE+ detection and load test for voltage drop
  • DHCP test
  • Traceroute
  • Switch port identification by blinking the port LED
  • The results can be saved in the NetXpert 1400 and full colour reports can be generated for documentation purposes.

 

KIT INCLUDES:
 netxpert1400-kit
 1 NetXpert Main Unit
1 Active remote
2 Power supply
1x 4 GB SD card
1 Micro USB cable
1 set Network and coax remote set (each #1-5),
F-conn coupler
2 Network patch cable
2 Sacrificial cable
2 Hanging strap and clip
1 Hard carrying case